New 2X HF Bias Tee DC Feeder 50K-60MHz For Wave RTL SDR LNA HAM Radio Amplifier

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
New 2X HF Bias Tee DC Feeder 50K-60MHz For Wave RTL SDR LNA HAM Radio Amplifier
Popular
Popular
Product Introduction
Description:
RF microwave flow biaser, DC feed
Use:
1. Active antenna RF power supply
2. The output of the wideband amplifier is blocked
3. Communication data is injected through the RF side
Working parameters:
1. Frequency range: 50K-60MHz
2. Insertion loss: 0.1dB@100KHz 0.2dB@60MHz
3. Maximum voltage: 50V
4. Maximum current: 600mA
5. RF connector: SMA-K (outer screw inner hole)
6. System impedance: 50 ohms
7. Dimensions: 33mmx33mm without connectors
Wiring method:
1. DC: external DC power supply
2. RF: RF signal end (this port can only transmit RF signals)
3. RF+DC: RF DC offset (this port can transmit RF and DC offset)
4. GND-: Common ground terminal for DC power supply
5. VCC+: DC power supply terminal
Package Included:
2PCS  B50K-60MHz HF Bias Tee DC Feeder For Wave RTL SDR LNA HAM Radio Amplifier Antenna
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
New 2X HF Bias Tee DC Feeder 50K-60MHz For Wave RTL SDR LNA HAM Radio Amplifier
Product Introduction
Description:
RF microwave flow biaser, DC feed
Use:
1. Active antenna RF power supply
2. The output of the wideband amplifier is blocked
3. Communication data is injected through the RF side
Working parameters:
1. Frequency range: 50K-60MHz
2. Insertion loss: 0.1dB@100KHz 0.2dB@60MHz
3. Maximum voltage: 50V
4. Maximum current: 600mA
5. RF connector: SMA-K (outer screw inner hole)
6. System impedance: 50 ohms
7. Dimensions: 33mmx33mm without connectors
Wiring method:
1. DC: external DC power supply
2. RF: RF signal end (this port can only transmit RF signals)
3. RF+DC: RF DC offset (this port can transmit RF and DC offset)
4. GND-: Common ground terminal for DC power supply
5. VCC+: DC power supply terminal
Package Included:
2PCS  B50K-60MHz HF Bias Tee DC Feeder For Wave RTL SDR LNA HAM Radio Amplifier Antenna
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.